REPLIQUES
Replies Power replicas: by law, any sale of projectile launcher developed the energy output of barrel is equal to or greater than 2 Joules must be declared Army (7th grade). Measurements of power is usually compared to the output speed (FPS or feet per second) and weight of the projectile (0.20 gram ball usually used for reference). Indeed it is kinetic energy. Launcher: They operate through a battery operating a system of gables and a resort and a piston that propels the ball. Replicas of weapons used by airsoft players are not considered weapons under the 1995 decree. But they are subject to Decree No. 99-240 of 24 March 1999 concerning the conditions of some objects the appearance of a firearm. The decree does not regulate in any way transport (banned in public places if the reply is visible) or the use of replica firearms but only their marketing as the title states. Balls: They have a diameter of 6 mm (or 8-mm rare models) plastic (biodegradable or not). There are different qualities of different weights and balls (0.12 g, 0.18 g, 0.20 g, 0.23 g, 0.25 g, 0.28 g, 0.29 g, 0.30 g, 0.36 g, 0.43 g, 0.45 g, etc.).. It mainly uses weights between 0.20 g and 0.25 g, heavier ball is rather reserved for shooting accuracy. The rate of output decline with increasing weight of the ball, but its stability is in the air is increased. It allows for a more stable and resistance to higher wind (which represents a significant interest when drawing with a launcher "manual", or "spring", a very firing low). Replicas Gas The gas lines are divided into 2 distinct categories: The GBB (Gas Blow-Back) Their operating principle is based on the principle of semi-automatic, each pressure on the trigger causes the percussion of a valve which will release some gas. It will propel the ball and operate a power pump that will have the effect of reducing the bolt back and then forward through a spring. This allows the introduction of a new ball in the firing room. Given their active ingredient (gas, often a refrigerator or a derivative of propane in liquid), performance (power) are strongly influenced by temperature. Indeed, below 0 ° C or low temperature, almost no GBB not working properly, gas had no opportunity to dilate properly. These replicas can be learned piecemeal (semi-automatic) or bursts (automatic), depending on their type and their internal mechanics.  KSC Glock 19 The NBB (Non Blow-Back): The system is simplified in the extreme. Here the gas is only used to propel the ball. The cylinder head was more mobile, resulting in a saving significant gas which can take many more balls. The loading balls made by a mechanical system operated by the relaxation of the replica, which explains the relative hardness of the race to relax. These replicas will not take that semi-automatic, since the automatic firing modes require a movement of cargo. There are replicas using carbon dioxide or of compressed air, including some replicas automatic, air is contained in cylinders similar to those used in paintball (their capacity is relatively limited given the complex mechanism employee) . Note that these very powerful aftershocks (about 400 fps) are often banned in parts. Replicas Manual Spring, replies manual (called "spring" -> spring): rearmament is manual, this principle is mainly used on replicas of guns or pistols and pumps should be to equip each shot. The bolts or replicas of precision: limited ball but with a greater range / precision, they operate on the principle of spring but with particular improvement in the strength of the parts used. They are relatively noisy, but their rate of fire is limited and the force used to reset the spring each shot increases the strength of spring used. Replicas Electrical The automatic launcher (or AEG, for Automatic Electric Gun): they eject the ball burst through an electrical system relatively simple: A battery supplies energy an engine resulting in gear that will themselves lead a piston that will tablet in resort. Once the cycle is complete, the gears release the plunger that will compress a volume of air more or less depending on the cylinder installed by the spring (which will relax violently). These replicas can use self-sustained and relatively high in terms of capacity and the power of the battery used. Their power is changed by simply changing the resort, but the strengthening of many pieces may be necessary to maintain the reliability of the reply and avoid breakage. Their operating principle is similar to replicas therefore spring but with the help of an electrical system.
Role of different parts: Here is a list of parts and their function. Gearbox (shell): maintains all other parts. Spring (spring): compresses when piston back and expels with energy. Gears (engrennages): operated by the engine, they cause the piston to the rear. Piston: declined by gears (gears) it serves as a guide to the piston head. Piston head: Hunting air to the cylinder head. Cylinder: contains the airflow ejected in the canon (compressed air propelling the ball). Anti-Reversal Latch (anti-notch return): prevents the wheels from turning in the wrong direction. Bushing / bearing: maintain the gears in place and facilitates their rotary movement. Spring Guide (guide spring): guide the resort and that he relaxes correctly. Engine / engine: leads gears (gears). Noozle (beak air): manages the arrival of balls in the barrel and concentrates the airflow on the ball. TAPPET Plate (range): operates Synchronize noozle. Cylinder head: regulates the flow of air before and towards the nozzle.
A IRSOFT A DVENTURE C LUB E X T RE M E ! ! !
AAC Look for on the site
Diary Association Member Office Club Wallpaper Combat G Ecology Minors Official Web site of the Haute-Savoie
Airsoft Repliques MemberFor every knowledge on our association in some clicks in .........
For every knowledge on our association in some clicks in .........
Reception Wallpaper Wallpaper Teams Shopswww.airsoft-haute-savoie.com Anthony Debure - 108 descente de st antoine - 74190 PASSY - 06 76 95 49 53
Shops Contact Links Chat-Forum Pictures
Replies Power replicas: by law, any sale of projectile launcher developed the energy output of barrel is equal to or greater than 2 Joules must be declared Army (7th grade). Measurements of power is usually compared to the output speed (FPS or feet per second) and weight of the projectile (0.20 gram ball usually used for reference). Indeed it is kinetic energy. Launcher: They operate through a battery operating a system of gables and a resort and a piston that propels the ball. Replicas of weapons used by airsoft players are not considered weapons under the 1995 decree. But they are subject to Decree No. 99-240 of 24 March 1999 concerning the conditions of some objects the appearance of a firearm. The decree does not regulate in any way transport (banned in public places if the reply is visible) or the use of replica firearms but only their marketing as the title states. Balls: They have a diameter of 6 mm (or 8-mm rare models) plastic (biodegradable or not). There are different qualities of different weights and balls (0.12 g, 0.18 g, 0.20 g, 0.23 g, 0.25 g, 0.28 g, 0.29 g, 0.30 g, 0.36 g, 0.43 g, 0.45 g, etc.).. It mainly uses weights between 0.20 g and 0.25 g, heavier ball is rather reserved for shooting accuracy. The rate of output decline with increasing weight of the ball, but its stability is in the air is increased. It allows for a more stable and resistance to higher wind (which represents a significant interest when drawing with a launcher "manual", or "spring", a very firing low). Replicas Gas The gas lines are divided into 2 distinct categories: The GBB (Gas Blow-Back) Their operating principle is based on the principle of semi-automatic, each pressure on the trigger causes the percussion of a valve which will release some gas. It will propel the ball and operate a power pump that will have the effect of reducing the bolt back and then forward through a spring. This allows the introduction of a new ball in the firing room. Given their active ingredient (gas, often a refrigerator or a derivative of propane in liquid), performance (power) are strongly influenced by temperature. Indeed, below 0 ° C or low temperature, almost no GBB not working properly, gas had no opportunity to dilate properly. These replicas can be learned piecemeal (semi-automatic) or bursts (automatic), depending on their type and their internal mechanics.  KSC Glock 19 The NBB (Non Blow-Back): The system is simplified in the extreme. Here the gas is only used to propel the ball. The cylinder head was more mobile, resulting in a saving significant gas which can take many more balls. The loading balls made by a mechanical system operated by the relaxation of the replica, which explains the relative hardness of the race to relax. These replicas will not take that semi-automatic, since the automatic firing modes require a movement of cargo. There are replicas using carbon dioxide or of compressed air, including some replicas automatic, air is contained in cylinders similar to those used in paintball (their capacity is relatively limited given the complex mechanism employee) . Note that these very powerful aftershocks (about 400 fps) are often banned in parts. Replicas Manual Spring, replies manual (called "spring" -> spring): rearmament is manual, this principle is mainly used on replicas of guns or pistols and pumps should be to equip each shot. The bolts or replicas of precision: limited ball but with a greater range / precision, they operate on the principle of spring but with particular improvement in the strength of the parts used. They are relatively noisy, but their rate of fire is limited and the force used to reset the spring each shot increases the strength of spring used. Replicas Electrical The automatic launcher (or AEG, for Automatic Electric Gun): they eject the ball burst through an electrical system relatively simple: A battery supplies energy an engine resulting in gear that will themselves lead a piston that will tablet in resort. Once the cycle is complete, the gears release the plunger that will compress a volume of air more or less depending on the cylinder installed by the spring (which will relax violently). These replicas can use self-sustained and relatively high in terms of capacity and the power of the battery used. Their power is changed by simply changing the resort, but the strengthening of many pieces may be necessary to maintain the reliability of the reply and avoid breakage. Their operating principle is similar to replicas therefore spring but with the help of an electrical system.
Role of different parts: Here is a list of parts and their function. Gearbox (shell): maintains all other parts. Spring (spring): compresses when piston back and expels with energy. Gears (engrennages): operated by the engine, they cause the piston to the rear. Piston: declined by gears (gears) it serves as a guide to the piston head. Piston head: Hunting air to the cylinder head. Cylinder: contains the airflow ejected in the canon (compressed air propelling the ball). Anti-Reversal Latch (anti-notch return): prevents the wheels from turning in the wrong direction. Bushing / bearing: maintain the gears in place and facilitates their rotary movement. Spring Guide (guide spring): guide the resort and that he relaxes correctly. Engine / engine: leads gears (gears). Noozle (beak air): manages the arrival of balls in the barrel and concentrates the airflow on the ball. TAPPET Plate (range): operates Synchronize noozle. Cylinder head: regulates the flow of air before and towards the nozzle.
A IRSOFT A DVENTURE C LUB E X T RE M E ! ! !
AAC Look for on the site
Diary Association Member Office Club Wallpaper Combat G Ecology Minors Official Web site of the Haute-Savoie
Airsoft Repliques MemberFor every knowledge on our association in some clicks in .........
For every knowledge on our association in some clicks in .........
Reception Wallpaper Wallpaper Teams Shopswww.airsoft-haute-savoie.com Anthony Debure - 108 descente de st antoine - 74190 PASSY - 06 76 95 49 53
Shops Contact Links Chat-Forum Pictures